www.esoftwaresource.blogspot.com. Powered by Blogger.
RSS

Canon IP4700 reset

The best way to reset Canon Pixma IP4700


Reset canon pixma ip4700 printer


Error ink cartridges aren't installed correctly


Primary power off the inkjet printer. Following, while holding Stop/Reset button, power on the printer.
While keeping power button, release Stop/Reset button.
After that push Stop/Reset button two times.
Wait around 20-30 seconds before the led shows “0".
Next press Stop/Reset button 4 times.
Lastly push Power button 2 times. Final action is to turn off the printer's through pressing the power button 1 final time.

The correct way to Reset waste ink counter (Error E16)


Unplug power and also USB cable.
Open door and maintain power button.
Connect power.
Close door, after that release power button.

This printer utilizes the following ink cartridges



  • Canon PGI-520BK


  • Canon CLI-521BK


  • Canon CLI-521C


  • Canon CLI-521M


  • Canon CLI-521Y

    • Digg
    • Del.icio.us
    • StumbleUpon
    • Reddit
    • RSS

    Canon mp250 reset waste ink

    How to reset Canon Pixma MP250 wasted ink


    Unplug the power cord and USB cable.

    Open the lid and hold down the power button.

    Plug the power cord.

    Close the door and release the power button.

    Reset Canon mp250


    Ready, your machine is ready for use!



    This printer uses the following cartridges


    Black cartridge PG-510

    Page yield pg510: 401 pages
    cartridge pg 510


    Optional black cartridge PG-512


    Clour cartridge CL-511

    Page yield cl511: 244 pages

    cartridge cl 511


    Optional clour cartridge CL-513

    • Digg
    • Del.icio.us
    • StumbleUpon
    • Reddit
    • RSS

    Reset Canon Pixma IP2600

    How to reset Canon ip 2600 Pixma All in one printer


    Reset ip 2600 canon Pixma All in one
    1. Power off the printer.
    2. Next, while holding STOP/RESET button, power on the printer.
      While holding POWER button, release STOP/RESET button. 
    3. Then push STOP/RESET button twice. Wait about 20-30 second until the LED shows “0″. 
    4. Then push STOP/RESET button four times.
      Finally push POWER button twice. 
    5. Last step is to turn off the printer by pressing the POWER button one last time.

    This printer uses the following ink cartridges



  • Canon PG-37


  • Canon PG-40


  • Refill canon PG-40
  • Canon CL-38


  • Canon CL-41


  • Refill canon CL41

      • Digg
      • Del.icio.us
      • StumbleUpon
      • Reddit
      • RSS

      Canon IP1900 reset waste ink

      How to reset Canon Pixma IP1900 wasted ink


      Unplug the power cord and USB cable.

      Open the lid and hold down the power button.

      Plug the power cord.

      Close the door and release the power button.



      Ready, your machine is ready for use!



      Canon IP1900 this printer uses the following cartridges

      PG40






      PG30





      CL31









      CL41

      • Digg
      • Del.icio.us
      • StumbleUpon
      • Reddit
      • RSS

      Masalah Kesihatan Akibat Penggunaan Komputer



      Nota kali ini adalah mengenai dua kesan terhadap kesihatan yang mungkin anda akan hadapi jika tidak mematuhi cara-cara penggunaan komputer yang betul.
      Dua kesan ini adalah Repetitive Strain Injury (RSI) dan Computer Vision Sydrome (CVS). Kita mulakan dengan RSI. RSI atau dengan nama lain "cumulative trauma disorder" atau "repetitive motion injury" adalah sejenis kecederaan yang berlaku kepada tisu lembut di dalam badan seperti tisu otot, saraf dan sendi menjadi sakit dan membengkak. RSI sering dilaporkan berlaku kepada mereka yang melakukan kerja yang sama berulang kali seperti di kilang pemasangan,bahagian penbungkusan, menjahit, bermain alatan muzik dan pekerja komputer. Banyak pekerjaan yang melibatkan tugas anggota badan melakukan kerja yang sama boleh pada jangka masa yang lama terdedah kepada masalah ini.

      Sebab-sebab RSI belum diketahui. Namun RSI telah dikaitkan dengan
      - Aktiviti atau pergerakan berterusan tanpa henti.
      - Melakukan aktiviti dalam posisi yang kekok dan tidak natural.
      - Mengekalkan posisi yang tetap untuk jangka masa yang panjang.
      - Tidak berhenti untuk berehat sekejap.
      - Keadaan sekeliling dan faktor sosial.

      Laporan tambahan juga menyebut RSI juga dikaitkan dengan penggunaan papan kunci, tetikus dan lain-lain alat input komputer. Mereka yang mempunyai penyakit seperti sakit sendi, kegemukan dan kencing manis
      juga terdedah kepada kecederaan ini.
      Sesetengah pengguna komputer mungkin merasai sakit atau tidak selesa apabila menggunakan komputer. Rasa tidak selesa ini mungkin tanda-tanda RSI.
      Anda perlu menggunakan komputer dengan cara yang betul. Menggunakan peralatan yang baik dan diletakkan dengan baik mungkin tidak banyak membantu. Anda perlu sentiasa dalam posisi dan kedudukan yang sesuai akan memberikan anda keselesaan yang anda mahukan.

      Nota diatas hanya cadangan dan penerangan yang tidak lengkap. Jika anda merasakan tidak selesa dan sakit sewaktu menggunakan komputer dapatkan pendapat doktor tentang itu. Lebih awal penyakit anda
      dikenal pasti lebih cepat ia diubati dan mengelakkan anda mengalami masalah kesihatan yang lebih panjang.

      CVS dipercayai disebabkan oleh cara bagaimana text dipancarkan di skrin komputer. Berbanding dengan tulisan atau cetakan pada kertas, text pada skrin komputer adalah cantuman pixel yang tebal
      ditengah tetapi berjerigi di tepi. Jika text di komputer diperiksa dengan kata pembesar kita akan dapat melihat kesan tidak rata dan tidak licin pada sempadan huruf text ini.
      Kesan ini menyebabkan mata tidak dapat memberikan fokus yang betul kepada huruf-huruf yang dipaparkan. Amata akan sentiasa membetulkan fokusnya dan ini akan meletihkan mata.

      Jika anda mengalami sakit kepala, pedih mata, rasa mual anda mungkin telah terlalu lama menggunakan komputer dan memandang lama skrin komputer anda mungkin mengalami masalah CVS.

      Langkah-langkah yang anda perlu lakukan untuk memastikan persekitaran
      penggunaan komputer anda adalah sesuai untuk anda,

      _____________

      Kawasan kerja
      _____________

      Kawasan kerja perlulah selesa dan mempunyai suhu dan kelembapan yang sesuai untuk komputer. Suhu yang terlalu panas bukan sahaja menyebabkan anda tidak selesa malah menyebabkan komputer anda mudah rosak. Suhu yang dicadangkan adalah sekitar 19 ke 23 darjah Celcius dan kelembapan sekitar 40 ke 60 peratus. Anda juga perlu pastikan kawasan penggunaan komputer mempunyai edaran udara yang baik.
      Pastikan keadaan sekeliling adalah senyap dan jauh daripada gangguan. Gangguan seperti kawasan laluan atau jika di rumah ia berdekatan kawasan TV atau radio. Gangguan bunyi bising akan mengganggu tumpuan
      anda. Bunyi sekeliling perlulah dibawah 55 dBA.Untuk keselesaan mata bilik yang anda gunakan perlu dicat dengan cat yang tidak menyerlah. Ia perlu dicat dengan warna yang lembut, tidak terlalu terang dan menyejukkan mata.

      Untuk mengelakkan kejang otot, pastikan anda mempunyai ruang pergerakan yang baik dan luas. Cuba jangan berada dalam posisi yang sama untuk jangka masa yang lama.Cahaya yang sesuai adalah penting untuk keselesaan mata. Sinaran lampu yang ada membolehkan anda membaca dokumen dan melihat huruf-huruf
      di papan kunci. Takat pencahayaan yang sesuai adalah antara 300 dan 500 Lux. Lebih daripada 1000 lux dianggap terlalu terang. Untuk kerja- kerja skrin komputer 300 lux adalah sesuai. 500 lux sesuai untuk
      tujuan membaca dokumen. Adalah dicadangkan lampu utama (lampu bilik) sekitar 300 lux dan sebuah lambu khas yang menyuluh dokumen anda dalam 500 lux boleh disediakan. Jika tiada kemudahan itu lampu utama
      perlulah berada dalam takat 500 lux. Pastikan tiada balikan lampu atau sumber cahaya yang terang pada skrin
      monitor anda. Sesuaikan supaya bahagian paling atas monitor berada bawah mata. Pastikan pancaran monitor anda tidak berkelip atau bergoyang. Ini boleh meletihkan mata.
      ____________

      Keadaan Anda
      ____________

      Pastikan jarak mata anda dengan skrin monitor sekitar 46 ke 76 cm. (sekitar 2 kaki). Jika anda mendapati diri anda mendekat diri kepada monitor kurang daripada jarak ini, pastikan anda membuat pemeriksaan mata.Kedudukan kepala anda sepatutnya 20 darjah menunduk kebawah. Apabila anda duduk, pastikan anda boleh duduk dengan tegak dan disokong dengan penyokong kerusi. Pastikan tangan anda oleh bergerak
      dengan bebas dan pergelangan tangan digunakan dalam keadaan LURUS.Papan kunci anda sepatutnya ada bahagian untuk meletakkan pergelangan tangan yang memolehkan pergelangan tangan dalam keadaan lurus.
      Anda sepatutnya tukarkan keadaan diri anda selalu. Jangan berada dalam satu kedudukan untuk jangka masa yang lama. Berhenti untuk berehat 5 ke 10 seminit dalam jangka masa sejam penggunaan komputer.
      Rehat sekejap adalah lebih baik daripada berehat panjang tetapi menggunakan komputer dua hingga tiga jam tanpa henti.Tukaran antara tugas antara menaip, berhenti sekejap untuk membaca, menulis, mengemas fail dan bergerak sekitar kawasan kerja boleh megelakkan masalah kekejangan urat. Lakukan senaman ringan
      pada tangan, kaki, bahu, leher dan belakang selalu, sekurangnya sejam sekali.

      Panduan diatas hanya pandangan peribadi hasil bacaan bahan-bahan di Internet dan buku-buku kesihatan. Anda PERLU mendapat nasihat doktor jika anda menghadapi masalah kesihatan yang mungkin bukan
      datang daripada RSI dan CVS.

      • Digg
      • Del.icio.us
      • StumbleUpon
      • Reddit
      • RSS

      How to Reset Cartridge of Canon MP198 / MP190 Printer

      https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEgKcJJ3itaaykNSXbYoLb_ut3AMgvBdOuI2s3yf4vdwwKBc76jbT_bOVgng-giK-Df1qyEMFV4BqpGg-COXlXfCQxxBjp76SQmhfIzwh7kYT9w7hVsQcOBxTnE3ye30bUkBTmAyqbUQE5tx/s1600/canon+mp198.jpg

      Problem: After refilling the cartridge of your Canon MP198 / MP190 printer, there is still an error that says your colored or black cartridge is still empty.

      Solution: This is a common problem when you refill the ink cartridge of you canon printer. You can bypass this problem by pressing the Stop/Reset button on bottom right hand side of the printer for about 5 seconds until the display reads 1 again. This will bypass the ink level sensor but your machine won't know how much ink left in the tank. It's not a problem though because it will let you print. Do this every time you refill your ink cartridge.

      • Digg
      • Del.icio.us
      • StumbleUpon
      • Reddit
      • RSS

      How To Repair Canon Pixma MP780 / MP760 / MP730 - Clogged Purge Unit


      1) Open the cover to get at the ink tanks and when the carriage comes to the center pull the power plug on the printer, then move the printhead more to the left.

      2) Have a syringe ready or an eye dropper with some Windex-Original with Amomnia D.

      Use a flash light to see into the right side of the open area where you can reach the ink Caps. These are the small rectangular suction units where the printhead sets all the way to the right. When the carriage is Parked, these ink caps come up and cover the inkjet nozzles. There is one on the left for the black and one on the right for the color.

      3) Add several drops of Windex to each cap until they appear flooded.

      The windex should begin to absorb through the Caps and down through the purge tubes to the waste ink pads. If it all goes in, add a couple of more drops.

      4) Plug the power back in and turn the printer on.

      The carriage will move through a couple of cycles and you should hear the purge unit doing a couple of cycles. One is for the black ink and the other one is for all the other colors.

      5) Close the cover and let the head do a parking cycle. This takes 55 seconds.

      6) Once it is parked turn the printer off and then on again with the power button. The power on cycle will force the printer to do a purge cycle just to test the purge unit. This is all part of the Canon power on Diagnostic routine.

      7) When it is finished and comes ready, raise the cover again and use your light to see if all the Windex is gone from the ink Caps. If you can reach the ink caps, add some more windex and repeat the cycle by closing the cover and cycling the power.

      8) Keep doing this if the ink Caps appear to be getting cleaner. It could also break up any clog that might be there, but you may have to repeat the process several times.

      If that doesn't clear up the problem, maybe the clog is not actually in the purge pump but rather in the tube coming from the bottom of the purge unit to the entrance of the peristaltic pump. You cannot unclog this tubing from the top of the purge unit. You will need to take apart the printer and get to the other end of the same tubing and squirt some Windex into it. The process for dismantiling the printer is the same as for changing the waste ink absorber pads.

      • Digg
      • Del.icio.us
      • StumbleUpon
      • Reddit
      • RSS

      How to Disassemble Canon MP780/MP760 Printer to replace the Waste Ink Pads

      There are four different types of screws and you want to get them back where they came from. To help you keep the screws straight, I have labeled the photographs with letters corresponding to each screw type. Here are the screw types:

      A: medium length plastic screw.
      B: short machine screw with integrated washer.
      C: longer plastic screw with integrated washer.
      D: shorter plastic screw.

      Before you attempt this process, you should remove the cartridges, do a deep head cleaning followed by a nozzle check and repeat until nothing prints. Then remove the print head and unplug the printer with the carriage still in the center of the printer.

      You will need a medium Phillips screwdriver with a long shaft (at least five inches long).

      Start by removing the two side panels. First remove these two screws from the front of the printer:

      Canon MP 780 / MP 760 Disassembly Guide

      Remove these four screws from the rear of the printer:



      Now pry off the back of each side panel over the two posts that the rear screws were removed from, pull each panel away from the printer and forward to release it from the printer. Be very careful of the timing wheel exposed on the left side of the printer during subsequent handling. You don't want to get it dirty or damage it.

      Next you have to remove the scanner unit. This is the most difficult part of this job. Remove all the wires and cables that pass from the scanner along the right hand hinge point being very careful to note where each cable goes. Some of the ribbon cables are held tightly in their connectors with a locking frame. You need to pull these out (but not off) to release those ribbon cables and of course you have to press the frames back in after you carefully return the cables to their proper positions. You also have to remove a couple plastic retainers. Look carefully at how they snap into place so that you can unsnap them without breaking them. It would be a good idea to take pictures and notes so that you can get it back together again. Here are pictures of this area for the MP760 (the MP780 is slightly different):


      After all the cables and wires are off the connectors (and the grounding wires unscrewed), gently pull the wires up through their feed holes up to the top of the printer.

      If you are working on an MP780, you can remove the upper part of the scanner. Open the cover until it is pointing almost straight up and then pull it out from the bottom scanner. You will have to wiggle it to get it free. Be careful of the wires on the right side. Bypass this step if you are working on an MP760.

      Next you will have to remove the two grey guides shown at the top of the first picture on this post. You do this by holding the scanner part way up so that the handle that you use to raise and lower the scanner is somewhat forward. Pull down on the top center of the guide and after the semi-circular protrusion is below its lock, slide the guide forward and remove it. Repeat for the other guide. Pay close attention to how these guides are removed so that you can get them back in place and be very careful that you don't break the semi-circular protrusion. It breaks very easily and if it does break, the guides will not stay in place unless you use an adhesive (tape or glue).

      Now you need to remove the bottom portion of the scanner from the printer (or the entire scanner if you have an MP760). Do this by opening it until it is straight up and lift it right out of its hinge points.

      Now with the scanner out of the way, you can remove four screws that hold the top of the printer in place. These four screws are located in approximately the four corners of the printer but you will have to raise the handle for the scanner to get to the one in the right front corner. Here are pictures of the screws in the four corners:

      Left rear:



      Right rear:



      Left front (get the correct screw, it's the one in front):



      And finally right front (you won't see this unless you raise the scanner handle):



      Make sure the handle for lifting the scanner (which has been removed) is latched down and simply lift the top of the printer away.

      Now you can see much of the printer mechanism. There is a total of seven or eight screws that need to be removed. (Disregard the sight of cables going everywhere, these pictures were taken from one of the printers that was broken and I was not concerned about restoring it.)

      Two screws on the left side of the printer:



      Two or three screws from the right rear of the printer (the one in the middle is higher than the other two and don't remove the two screws holding ground wires):



      And three more screws near the right center of the printer:



      Before you can lift the printer mechanism and the electronics board away from the base, you need to disconnect the wires that go to the left side of the electronics board (near the front of the printer) that are not colored orange or yellow. On the MP780 there are two pairs of wires and on the MP760 there is just one. The picture above shows these two wire pairs for the MP780 disconnected. These wires go along the underside of the printer to the other side.

      Slide the carriage as far right as it will go.

      Before you remove the printer mechanism from its base, you should observe the positions of a couple of white cams as seen circled in yellow in this picture:



      Don't worry if they come loose while you are removing the printer mechanism, just remember to put them back where they belong when re-assembling. Here is a closeup of the one on the right:



      Lift the mechanism up by the metal bar that goes across the top of the printer. As you first start to lift it, some orange cables near the front need to be unpositioned from their plastic guides in the base. Note how they are positioned so that you can get them back in the same orientation. This picture shows how these orange cables are positioned and how you need to return them when you are putting the printer back together:



      When you get the printer mechanism removed, this is what you'll see:



      Now you can easily remove the waste ink pads and clean up all the residual ink from the various plastic parts. Thoroughly dry it before installing new pads.

      You may also want to remove and wash the thin black sponge unit that runs the width of the printer. Also clean the wiper blades and the two purge pads. When you put them back, the notch goes in the left rear corner.

      Reassemble the printer by reversing all the steps. To help guide the printer into the base, look at the back of the printer and line up the door into the base unit. Make sure those two white tabs are inserted where they belong and are engaging the proper posts and make sure the orange wires make their way across their restraining tabs. Make sure you plug in the wires that run along the base of the printer.

      When putting the printer top on the printer, look at the back again and line up the door into the printer top.

      • Digg
      • Del.icio.us
      • StumbleUpon
      • Reddit
      • RSS

      How to Reset Canon MP760 - Waste Ink Tank Reset Procedure


      1) Press the following keys in sequence: Copy-Menu-Scan-Copy-Scan.
      The display will say:
      SERVICE MODE
      #1 SSSW

      2) Press the V key six times.
      The display will say:
      SERVICE MODE
      #7 PRINTER

      3) Press OK.
      The display will say:
      #7 PRINTER
      #1 SSSW

      4) Press the V key four times.
      The display will say:
      #7 PRINTER
      #5 INK ABS CAPA

      5) Press OK.
      The display will say:
      SUCTION
      XX (where XX is how full the waste ink tank is as an integer percentage)

      6) Change the XX to 0 by hitting the <> keys as many times as necessary (if you are closer to 99 than 0 it is better to hit the > key until it wraps around to 0).
      The display will say:
      SUCTION
      0

      7) Press OK.
      The display will momentarily say:
      SUCTION
      DATA ENTRY OK
      and then will quickly change to:
      #7 PRINTER
      #6 CDR ADJUST

      8) Press the Stop/Reset button

      And the printer is back to normal.

      • Digg
      • Del.icio.us
      • StumbleUpon
      • Reddit
      • RSS

      Quick Checklist: Common Causes of Computer Faults

      Almost every computer user has experienced operating failures at one time or another, such as crashing, not being able to turn on the computer, overheating and unstable noises. These symptoms can be attributed to a wide variety of issues like viruses, spyware, spam, incompatible components, unoptimized system settings, faulty hardware and old computer components.
      Hardware Conflicts and Bad RAM
      Many times, computer crashes are caused by hardware conflicts. When two hardware pieces, like a mouse and keyboard, share the same IRQ, or Interrupt Request Channel, a hardware conflict may occur. In order to avoid this aggravating problem, check the utilized IRQs. And if a device is sharing an IRQ with another device, reinstall the latest one.

      Bad RAM, or Random Access Memory, is also a common cause of computer crashes. Most fatal exception errors are attributed to either serious hardware issues or mismatched RAM chips. When two RAM chips operate at different speeds, the computer is forced to run both of them at a low speed, resulting in a crash. So make sure both chips are running at the same speed. You can also enter the BIOS settings and increase the RAM's wait state.

      BIOS Settings
      Every motherboard is preset at a specified chipset range. In some cases, the setting causes a computer to crash. To investigate within the BIOS settings, look for CAS latency/RAM discrepancies. New SDRAM utilizes a “2” latency while old RAM uses a “3” latency.

      Hard Disk Drives, OE Exceptions and Fatal VXD Errors
      If you use your computer daily, the hard drive becomes fragmented every few weeks. This is why experts suggest weekly disk defragmentation. Performing this simple task will keep a computer operating fast and smooth. OE Exceptions and Fatal VXD Errors are usually due to video card problems. These issues are easily remedied by reducing the video display's resolution.

      Spyware and Viruses
      Viruses and spyware are a main culprit of computer instability and crashes. Besides running malcious codes, viruses will operate, many times undetected, in the system's background. This eventually causing the entire operating system to crash. The best way to keep viruses at bay are to scan each document, picture and attachment you download as well as refrain from opening e-mails by unkown senders. And of course, always perform a regular virus scan and quarantine.

      Software and Printers
      When software is not installed properly, it can cause an operating-system crash. If you install new software and immediately experience instability problems, uninstall the software. If there is improvement, the software is the problem.

      Although it seems like they are fairly benign pieces of equipment, printers are also known to cause computer crashes. When a document is sent to the printer, the computer makes a postscript file. This file is larger than the original one. Because printers do not have big memories, they can easily become overloaded. If you are experience computer trouble during printing, turn the printer off for approximately 10 seconds and then, restart the printer.

      Power Supplies and Overheating
      Power supplies can cause a uprising amount of damage to a computer during a power outage or surge. It is recommended that every computer be plugged into an uninterrupted surge protector. Although this does not eliminate the chance of a power overload, a surge protector does significantly reduce the risk.

      When a tower overheats, also known as a kernel error, the computer may make loud noises and internal components could become damaged. CPUs produce a lot of heat during operation. If your computer's fan is generating an overpowering noise, chances are you need to install a larger aftermarket fan.

      • Digg
      • Del.icio.us
      • StumbleUpon
      • Reddit
      • RSS

      How want to fast broadband

      As Muslims start with the

       


       1) Click on Start Button.

      2) Select Run From Start Menu.

      3) Taip gpedit.msc
       
      4) klik [Administrative Templates] branch. 

      5) klik [Network] branch.

      6) Highlight(Select by Single Click) [QoS Packet Scheduler]

      7) Double-click [Limit Reservable Bandwidth] (Available in Right Side Panel)

      8) Check(Select By Single Click on it) [Enabled]

      9) Change [Bandwidth limit %] to 0 %. Contoh bergambar seperti dibawah yea.

       
      10) Click [OK] Button.

      11) Restart Your PC.

      12) Now Check Your Broadband Speed.
       

      • Digg
      • Del.icio.us
      • StumbleUpon
      • Reddit
      • RSS

      33 TUTORIAL PHOTOSHOP BAHASA MALAYSIA

       

      01.Foto dalam Imej Pemandangan
      02.Membersihkan Wajah Di Foto
      03.Titisan Air Di Daun
      04.Mencipta Bola Kristal
      05.Teks di Lengkungan Cawan
      06.Cantuman Dua Imej
      07.Cantuman Beberapa Imej
      08.Menukar Foto Kepada Lukisan
      09.Iklan Di Kota Raya
      10.Membuat Kibaran Pada Bendera
      11.Imej Di Kiub
      12.Bingkai Kabur Di tepi Imej
      13.Selembar Album Sebagai Bingkai
      14.Membina Strip Filem
      15.Efek Teks Glass
      16.Efek Teks Glass 2
      17.Efek Teks Cermin
      18.Efek Teks Mengikut Kontur
      19.Mencipta Logo 1
      20.Mencipta Logo 2
      21.Mencipta Logo 3
      22.Membina Kad Perniagaan

      • Digg
      • Del.icio.us
      • StumbleUpon
      • Reddit
      • RSS

      Masalah "Generic volume cannot be stopped right now"

      Pernahkah anda menghadapi error atau masalah semasa remove usb, memory card dan sewaktu dengannya di mana keluar error "Generic volume cannot be stopped right now".


      penyelesaian :

      Kaedah 1 :

      1.Pastikan anda telah tutup semua file,folder atau program yang di buka daripada memory atau usb tersebut.

      Kaedah 2 :

      1. Anda menggunakan perisian unlocker untuk menyelesaikan masalah di atas tersebut.
      2. Download di sini unlocker.

      apa itu Unlocker?
      Unlocker adalah explorer extension yang membolehkan anda klik kanan pada sesuatu file, folder atau pen drive bagi memusnahkan atau menghapuskan error message seperti di atas.

      • Digg
      • Del.icio.us
      • StumbleUpon
      • Reddit
      • RSS

      Kepentingan Screen Saver

      Adakah anda tahu bertapa bergunanya screen saver untuk penjagaan screen lcd  kita??Dengan adanya fungsi ini,lcd kita dapat diselamatkan daripada kerosakan.Walaupun begitu,setiap perkakasan akan rosak apabila tiba masa nya.Tetapi,langkah pencegahan kita adalah melambatkan tempoh kerosakan itu.Kalau kita fikirkan, nama pun screen saver di tejermahkan akan bermaksud penyelamat screen. Dengan ini sebenarnya memberi kebaikan kepada screen iaitu menyelamat screen. Antaranya screensaver berfungsi untuk menambah umur monitor atau screen. sekiranya monitor dibiarkan hidup tanpa menggunakan screensaver maka akan mengurangi umur monitor tersebut.Screen saver biasanya terdiri daripada 3 warna asas yang menampilkan warna merah, Hijau dan Biru. ini juga kerana monitor komputer menggunakan sistem warna RGB (Red Green Blue) maka screensaver biasanya menampilkan warna-warna tersebut secara bergantian ketika sedang berfungsi dan ia bertujuan untuk mencegah agar monitor tersebut tidak cepat rosak.

      antara fungsi yang dapat di simpulkan lagi:-

      • memanjangkan umur monitor atau screen
      • mencegah screen atau monitor cepat rosak

      • Digg
      • Del.icio.us
      • StumbleUpon
      • Reddit
      • RSS

      Masalah 'Monitor Out of Range'

       Artikal kali ini,saya ingin berkongsi mengenai masalah 'monitor out of range'bagi penggunaan komputer jenis desktop.Perkara ini berlaku kerana,resolution yang di-setting untuk monitor terlalu tinggi.Contoh,hertz minitor pada keadaan yang sesuai adalah 60 hertz tetapi kalau tersalah setting kepada 70 hertz akan keluar error 'monitor out of range'.Oleh itu,jangan panik,atau tergesa-gesa untuk hantar ke mana-mana kedai komputer kerana hasil tinjauan saya,teknikal tersebut akan memberi alasan seperti berikut:
      1. monitor rosak
      2. graphic card rosak
      3. windows corrupted
      Semua ini adalah alasan kedai semata-mata untuk mengaut keuntungan (bagi yang tidak jujur je,bukan semua tapi ada sesetengah kedai sahaja)
      Apa yang perlu dilakukan adalah:
      1.On pc dan tekan F8 sehingga keluar paparan berikut.

      2.Pilih pada menu 'Enable VGA Mode'

      3.Selepas itu,anda akan dapat masuk ke windows seperti biasa.



      4.Letak cursor mouse di mana-mana bahagian di desktop right click --> properties --> setting --> advanced --> monitor --> screen refresh rate: pilih 60 hertz -->OK 



      ---> SELESAI <---

      • Digg
      • Del.icio.us
      • StumbleUpon
      • Reddit
      • RSS